您好,歡迎光臨萊州中科聚峰機械有限公司官方網站! 鄭重聲明 進入官網

自動攪拌車進料堵塞應該注意什么?

來源:http://www.pingqxw.com/ 日期:2020-10-26 發布人:admin
由于混凝土會在短時間內凝固成硬塊,且對鋼材和油漆有一定的腐蝕性,所以每次使用混凝土貯罐后,洗凈粘附在混凝土貯罐及進出料口上的混凝土是每日維護必須認真進行的工作。其中包括:
Since the concrete will solidify into a hard block in a short time, and has certain corrosivity to steel and paint, it is a daily maintenance work to clean the concrete adhered to the concrete storage tank and the inlet and outlet after each use of the concrete tank. These include:
1.每次裝料前用水沖洗進料口,使進料口在裝料時保持濕潤;
1. Flush the feed inlet with water before each loading to keep it moist during loading;
2.在裝料的同時向隨車自帶的清洗用水水箱中注滿水;
2. At the same time of loading, fill the cleaning water tank attached with the vehicle with water;
3.裝料后沖洗進料口,洗凈進料口附近殘留的混凝土;
3. After loading, wash the inlet to clean the residual concrete near the inlet;
4.到工地卸料后,沖洗出料槽,然后向混凝土貯罐內加清洗用水30—40 L;在車輛回程時保持混凝土貯罐正向慢速轉動;
4. After unloading at the construction site, wash the discharge tank, and then add 30-40 l of cleaning water into the concrete storage tank; keep the concrete storage tank in forward and slow rotation when the vehicle returns;
中科攪拌機
5.下次裝料前切記放掉混凝土貯罐內的污水;
5. Remember to discharge the sewage in the concrete tank before the next loading;
6.每天收工時徹底清洗混凝土貯罐及進出料口周圍自動,自動攪拌車的清洗要點保證不粘有水泥及混凝土結塊。
Automatic cleaning of concrete storage tank and automatic cleaning of concrete storage tank.
1、上下料時間參數不合理:自動上料機因料倉內無法加裝料位機,所以行業基本都有時間控制。如何設置時間參數,上下料時間設置其實很簡單,在初次使用時,先設置一個小的時候,然后根據每次吸料位置慢慢加,當達到料位達到吸料口的時間,再減去一秒就是合理時間。放料時間是確保放完料再加一秒。這樣做有兩個好處:一是料位太高對濾芯傷害特別大,二是每次料都能放干凈。
1. Unreasonable loading and unloading time parameters: automatic feeding machine can not be installed in the silo, so the industry basically has time control. How to set the time parameter? The setting of loading and unloading time is very simple. In the first use, set a small time first, and then add slowly according to the suction position. When the material reaches the material level and reaches the suction port, subtracting one second is the reasonable time. The discharging time is to ensure that one second is added after discharging. This has two advantages: one is that the material level is too high to damage the filter element; the other is that the material can be put clean every time.
2、自動攪拌車進料口給料量是否合理:正確的方式是物料在吸料口和空氣形成一定的氣物混合比,在氣流的推動下均勻流入上料機。這個時候我們需要將料槍設計帶有補氣功能。如果物料積壓時間過長可能很硬,這個時候需要在料槍上裝一個振蕩器,敲碎結塊的物料。
2. Whether the feeding amount at the feeding port of the automatic feeding mixer is reasonable: the correct way is to form a certain air-material mixing ratio between the material at the suction port and the air, and evenly flow into the feeding machine under the driving of the air flow. At this time, we need to design the material gun with air replenishment function. If the material overstocking time is too long, it may be very hard. At this time, we need to install an oscillator on the material gun to break the agglomerated materials.
只有把上述所講的內容設定好,我們的操作才算完成,如果您這邊在后續的過程中有任何的問題,歡迎致電或者是在網站上邊留言:中科攪拌機http://www.pingqxw.com
If you have any problems in the follow-up process, please call or leave a message on the website: Zhongke mixer http://www.pingqxw.com

上一篇::水泥自動攪拌車剎車要做好這些注意!
下一篇:廠家對于車燈的保養應該注意什么?

Japanesemature高清无码